6 November 2026
Toughened Glass Thickness Guide: 3–25mm Chart & Uses
Toughened (tempered) glass is produced in a wide range of thicknesses — from 3 mm up to 25 mm — and picking the right one matters for both safety and cost. Too thin and the pane may not carry its load; thicker than needed and you pay for weight you don’t use. This guide explains how thickness is chosen and what to confirm before ordering.
What drives the thickness you need
The right thickness is a function of the application, not a single number. The main factors are:
- Pane size — larger panes need more thickness to stay rigid and resist deflection.
- Load — wind load on a façade, impact on a balustrade, or foot traffic on a glass floor all push the thickness up.
- Edge support and fixing — a frameless or point-fixed pane behaves differently from one held on four edges.
- Build-up — whether the toughened glass is used alone, laminated, or in an insulating unit.
Because of these variables, structural or safety-critical glazing (balustrades, floors, large façade panels) should always be sized by a façade engineer rather than from a rule of thumb.
Typical thickness ranges
As a general orientation — always confirm with your engineer or with us for the actual application:
- 4–6 mm — small panes, cabinet and furniture glass, appliance doors
- 8–10 mm — interior partitions, frameless doors, shower enclosures, smaller balustrades
- 10–12 mm — larger doors, balustrades and partitions; a common all-round structural thickness
- 15–19–25 mm — large façade panels, structural glazing and heavy-duty applications
8 mm and 10 mm are among the most common thicknesses asked for in partitions and balustrades, but the span and fixing decide the final choice.
Minimum thickness
“Minimum thickness” has two meanings worth separating:
- The thinnest we can temper. The thinnest toughened glass we produce is 3 mm (minimum pane size 100 × 300 mm). Thinner float glass cannot reliably hold the tempering stress, so 3 mm is the practical floor.
- The thinnest that is safe for your job. This is set by load and span, not by the production line. Small cabinet, furniture and appliance panes may use 4–6 mm, but any safety-glazing or structural position (doors, balustrades, façades, floors) needs more, and must be sized by an engineer. A pane that is strong enough as a sample can still be under-thickness once the opening size and wind load are known.
So do not specify the minimum thickness we can make — specify the minimum that carries your load at your pane size.
Curtain wall glass thickness
In a curtain wall the glass is almost always an insulated or laminated-insulated build-up, not a single pane, so “thickness” means the whole unit. Typical build-ups from our completed façade projects (each number is a glass ply or cavity, in mm):
- Double-glazed vision unit — e.g. 6 mm tempered + 12A + 6 mm tempered, or 8 + 12A + 8, where “12A” is a 12 mm sealed insulated cavity, usually with a Low-E coating on one pane.
- Laminated-insulated curtain wall — e.g. 6 mm heat-strengthened + 1.14 PVB + 6 mm + 12A + 6 mm tempered, where the outer leaf is a laminated pair for fall-through safety and the unit is then sealed into an IGU.
- High-spec station façade — e.g. 12 mm Low-E tempered + 12Ar (argon) + 8 mm tempered + 1.52 PVB + 8 mm tempered (Nanchang East Station), combining Low-E, an argon-filled cavity and a laminated inner leaf.
In practice curtain-wall vision glass runs 6–8 mm per tempered ply with a 12 mm (12A) cavity; larger feature, spandrel or structural panels go thicker, up to the 25 mm we can temper. The exact build is always set by wind load, pane size and the thermal/safety targets — send the elevation and we will confirm it.
Toughened glass specifications
| Spec | Value |
|---|---|
| Thickness | 3–25 mm |
| Size range | min 100 × 300 mm, up to 2850 × 6000 mm |
| Surface compression | ≥ 69 MPa (per EN 12150 / ASTM C1048) |
| Standards | GB 15763.2, EN 12150, ASTM C1048, AS/NZS 2208, BS 6206 |
Remember that toughened glass cannot be cut or drilled after tempering, so the thickness, size and all holes must be finalised before production.
Tell us the application, pane size and any load or standard you build to, and we will recommend a thickness and supply toughened glass from 3–25 mm. Send us your enquiry for a quote, EXW or FOB — or see our toughened (tempered) glass page.
Sources
- Client product catalogue / knowledge base (flat-tempered glass thickness range, size range, surface compression and standards)
- Client project catalogue (completed façade build-ups and curtain-wall glass configurations)
Related reading
Interested in our glass products?
Contact our export team for technical advice, samples and a competitive quotation.
Get a Quote