info@dayangglass.com +86-755-89715589

10 November 2026

Custom Tempered Glass: Sizes, Shapes, Holes & How to Order

Most projects do not fit a standard glass size. Custom tempered glass is toughened (tempered) safety glass cut, shaped and processed to your exact drawing — the right route when an off-the-shelf panel will not do. This guide covers what can be customised, and what a manufacturer needs from you to quote accurately.

What can be customised

  • Size. Panels cut to your exact width and height, within the processing range we confirm for the thickness you need.
  • Shape. Rectangles, circles, triangles, trapezoids and other cut-to-template shapes.
  • Thickness. A range of thicknesses to suit the span, load and application; we confirm the right one by calculation for your opening.
  • Edgework. Ground, polished, bevelled or arrissed edges, depending on whether the edge is framed or exposed.
  • Holes and cut-outs. Drilled holes, notches and corner cut-outs for hinges, patch fittings, handles and standoffs — set out on your drawing before tempering, because tempered glass cannot be cut or drilled afterwards.
  • Finish. Clear, low-iron (extra-clear), tinted, frosted/acid-etched or coated, where the application calls for it.

Why it must be made before tempering

Tempered glass gets its strength from a heat-treatment that locks the surfaces into compression. Once toughened, it cannot be cut, drilled or re-worked — any attempt shatters the panel. That is why every size, hole and cut-out is finished on the raw glass first and then tempered. Getting the drawing right up front is what keeps a custom order on time.

How to order custom tempered glass

To quote accurately, send us:

  1. Sizes and quantity — each panel’s dimensions and how many.
  2. Thickness (or the application, so we can advise it).
  3. A drawing showing shape, hole positions and cut-outs, with edge type.
  4. Finish — clear, low-iron, tinted, coated, etc.
  5. Destination and shipping terms (EXW or FOB) and any target date.

With that we confirm the processing range, the minimum order quantity and the lead time, and come back with an itemised quotation.

A supplier, not just a panel

As a tempered glass manufacturer we also combine toughened glass as laminated safety glass or in an insulated unit where the project needs it — so a single custom order can cover safety, acoustic and thermal requirements together. See the tempered (toughened) glass product page for the specification, then send us your sizes and drawing for a custom tempered glass quote.

Tempered glass specifications

Thickness. Flat tempered glass is produced from 3 mm to 25 mm. The correct thickness for a given opening depends on the pane dimensions, applied loads and whether the glass is monolithic or part of a laminated or insulated build-up — we confirm it by calculation.

Mechanical performance. The heat-treatment puts the glass surfaces into permanent compression, achieving a surface compressive stress of at least 69 MPa. The result is glass that is 3–5 times stronger than the equivalent annealed float glass. When a tempered pane breaks, it fractures into small, blunt fragments rather than sharp shards — the behaviour that qualifies it as safety glazing.

Finish options. Panels can be clear, low-iron, body-tinted, acid-etched or coated. Ceramic-frit printing can be applied before tempering for spandrel panels or shading. All cutting, drilling, edgework and coating must be completed on the raw glass before the furnace.

Standards. Manufactured to GB 15763.2, EN 12150 and ASTM C1048.

Sizes. Large-format, made-to-order and cut to your drawings; we confirm the achievable processing range for the thickness you need.

In the field

At a motorsport-venue façade, every ply in the laminated insulating units was tempered glass: a grey-tinted tempered outer ply laminated with a 1.52 mm PVB interlayer to a clear tempered inner ply, sealed over a 16 mm air cavity with a further clear tempered inner pane. Fully tempered plies throughout delivered the impact resistance a public venue requires; the laminated outer pane kept fragments bonded in place if broken; and the insulating cavity met the thermal performance target. Solar control, post-breakage safety and thermal performance in one unit — achievable because tempering, laminating and sealing were all done in-house.

Frequently asked questions

What thicknesses of custom tempered glass are available? From 3 mm to 25 mm. The right thickness depends on pane dimensions, loads and the build-up; we advise the correct specification from your drawings.

Can tempered glass be cut or drilled after toughening? No. Once tempered, the glass cannot be cut, drilled or re-worked — it will shatter. All dimensions, holes and edge profiles must be machined into the raw glass before tempering. A complete drawing before the order is placed is essential.

Which standards is your tempered glass produced to? Manufactured to GB 15763.2, EN 12150 and ASTM C1048, covering minimum surface compression, fragmentation and dimensional tolerances.

Can tempered glass be combined with lamination or an insulated unit? Yes. Tempered plies can be laminated with PVB or SGP, and the laminated panel — or a monolithic tempered pane — can be sealed into an insulated unit. See the laminated glass and insulated glass pages for details.

Send us your sizes and drawing and we will return a quotation with the confirmed specification, lead time and EXW / FOB pricing.

Related reading on sizing, cutting and sourcing tempered glass:

Interested in our glass products?

Contact our export team for technical advice, samples and a competitive quotation.

Get a Quote